Description

envlpx -- apply an envelope consisting of 3 segments:

Syntax

ares envlpx xamp, irise, idur, idec, ifn, iatss, iatdec [, ixmod]

kres envlpx kamp, irise, idur, idec, ifn, iatss, iatdec [, ixmod]

Initialization

irise -- rise time in seconds. A zero or negative value signifies no rise modification.

idur -- overall duration in seconds. A zero or negative value will cause initialization to be skipped.

idec -- decay time in seconds. Zero means no decay. An idec > idur will cause a truncated decay.

ifn -- function table number of stored rise shape with extended guard point.

iatss -- the ratio of the final value of the pseudo-steady-state period to the value at its beginning (i.e the attenuation from the end of the rise segment to the start of the decay). A ratio greater than 1 causes an exponential growth and a ratio less than 1 creates an exponential decay. A ratio of 1 will maintain a true steady state at the last rise value. Note that this attenuation is not at a fixed rate (as in a piano), but is sensitive to a note's duration. However, if iatss is negative (or if steady state < 4 k-periods) a fixed attenuation rate of abs(iatss) per second will be used. 0 is illegal.

iatdec -- the ratio of the value at the end of the decay period to the value at its beginning (the end of the steady-state segment) . It must be positive and is normally of the order of .01. A large or excessively small value is apt to produce a cutoff which is audible. A zero or negative value is illegal.

ixmod (optional, between +- .9 or so) -- exponential curve modifier, influencing the steepness of the exponential trajectory during the steady state. Values less than zero will cause an accelerated growth or decay towards the target (e.g. subito piano). Values greater than zero will cause a retarded growth or decay. The default value is zero (unmodified exponential).

Performance

kamp, xamp -- input amplitude signal.

Rise modifications are applied for the first irise seconds, and decay from time idur - idec. If these periods are separated in time there will be a steady state during which amp will be modified by the first exponential pattern. If the overall duration idur is exceeded in performance, the final decay will continue on in the same direction, tending asymptotically to zero.

Examples

Here is an example of the envlpx opcode. It uses the file envlpx.csd.

<CsoundSynthesizer>
<CsOptions>
; Select audio/midi flags here according to platform
-odac     ;;;realtime audio out
;-iadc    ;;;uncomment -iadc if realtime audio input is needed too
; For Non-realtime ouput leave only the line below:
; -o envlpx.wav -W ;;; for file output any platform
</CsOptions>
<CsInstruments>

sr = 44100
ksmps = 32
nchnls = 2
0dbfs = 1


instr 1

irise = 0.2
idec  = 0.5
idur  = p3 - idec

ifn = 1
iatss = p5
iatdec = 0.01

kenv envlpx .6, irise, idur, idec, ifn, iatss, iatdec
kcps = cpspch(p4)
asig vco2 kenv, kcps
;apply envlpx to the filter cut-off frequency
asig moogvcf asig, kcps + (kenv * 8 * kcps) , .5 ;the higher the pitch, the higher the filter cut-off frequency
     outs asig, asig

endin
</CsInstruments>
<CsScore>
; a linear rising envelope
f 1 0 129 -7 0 128 1

i 1 0 2 7.00 .1
i 1 + 2 7.02  1
i 1 + 2 7.03  2
i 1 + 2 7.05  3
e
</CsScore>
</CsoundSynthesizer>

See Also

envlpxr, linen, linenr

Credits

Thanks goes to Luis Jure for pointing out a mistake with iatss.