Description

Mixes an arate signal into a channel of a buss.

Syntax

MixerSend asignal, isend, ibuss, ichannel

Initialization

isend -- The number of the send, for example the number of the instrument sending the signal. The gain of the send is controlled by the MixerSetLevel opcode. The reason that the sends are numbered is to enable different levels for different sends to be set independently of the actual level of the signals.

ibuss -- The number of the buss, for example the number of the instrument receiving the signal.

ichannel -- The number of the channel. Each buss has nchnls channels.

Performance

asignal -- The signal that will be mixed into the indicated channel of the buss.

Use of the mixer requires that instruments setting gains have smaller numbers than instruments sending signals, and that instruments sending signals have smaller numbers than instruments receiving those signals. However, an instrument may have any number of sends or receives. After the final signal is received, MixerClear must be invoked to reset the busses to 0 before the next kperiod.

Examples

instr 100 ; Fluidsynth output
; INITIALIZATION
; Normalize so iamplitude for p5 of 80 == ampdb(80).
iamplitude 		= 			ampdb(p5) * 2.0
; AUDIO
aleft, aright 		fluidAllOut		giFluidsynth
asig1 			= 			aleft * iamplitude
asig2 			= 			aright * iamplitude
			; To the chorus.
			MixerSend		asig1, 100, 200, 0
			MixerSend		asig2, 100, 200, 1
			; To the reverb.
			MixerSend		asig1, 100, 210, 0
			MixerSend		asig2, 100, 210, 1
			; To the output.
			MixerSend		asig1, 100, 220, 0
			MixerSend		asig2, 100, 220, 1
endin

Here is a complete example of the MixerSend opcode. It uses the file Mixer.csd

<CsoundSynthesizer>
<CsOptions>
; Select audio/midi flags here according to platform
; Audio out   Audio in
-odac       ;   -iadc    ;;;RT audio out
; For Non-realtime ouput leave only the line below:
; -o Mixer.wav -W ;;; for file output any platform
</CsOptions>
<CsInstruments>

sr = 44100
ksmps =	32
nchnls = 2
0dbfs  = 1

instr 1

katt	expon 0.01, p3, 1		;create an attack
aout	poscil .7, 440,1
	MixerSetLevel	1, 3, katt	;impose attack on the gain level
	MixerSend aout, 1, 3, 0		;send to channel 0
endin

instr 2

aout	vco2 .5, 110			;saw wave
	MixerSetLevel 2, 3, .25		;set level to .25 of vco2
	MixerSend aout, 2, 3, 1		;send to channel 1
endin

instr 3	;mix instr.1 and 2 with reverb
	
kgain1	MixerGetLevel	1,3		;get level form buss 3
kgain2	MixerGetLevel	2,3		;get level form buss 3
a1	MixerReceive	3,0		;receive channel 0
a2	MixerReceive	3,1		;receive channel 1
aout	= a1*kgain1+a2*kgain2		;mix them
aoutL, aoutR reverbsc aout, aout,  0.85, 12000	;add a nice reverb
	outs  aoutL, aoutR
	MixerClear
endin

</CsInstruments>
<CsScore>
f1 0 4096 10 1

i1 0 2
i2 0 2
i3 0 8	;reverb stays on for 8 sec.

e
</CsScore>
</CsoundSynthesizer>

See also

Mixer Opcodes

Credits

Michael Gogins (gogins at pipeline dot com).